Disponibile Prodotto più richiesto
UST4C11
UST4C11 ST4-C11 PANASONIC Controller for ST4
$0.00USD
3452 in magazzino
Specifiche chiave
Articolo:Specifications
PFHD:Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.)
MTTFD:More than 100 years (Note：Mean time to dangerous failure (in years))
Peso:Net weight: 180 g approxGross weight: 390 g approx
Informazioni fornitore
PANASONIC
Prodotti: 4316
Di solito spedito entro 2-3 giorni lavorativi
Qualità garantita
Spedizione veloce
Supporto tecnico
Specifiche tecniche
| Parametro | Valore |
|---|---|
| Articolo | Specifications |
| PFHD | Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.) |
| MTTFD | More than 100 years (Note：Mean time to dangerous failure (in years)) |
| Peso | Net weight: 180 g approxGross weight: 390 g approx |
| Dettagli | Controller |
| Prodotto | Compact Type 4 Safety Beam Sensor |
| Materiale | Enclosure: ABS |
| Numero di parte | ST4-C11 |
| Nome del prodotto | Compact Type 4 Safety Beam Sensor ST4 |
| Cavo di cablaggio | Terminal block connector: 0.2 to 1.5 mm2 |
| Tensione di alimentazione | 24 V DC +10-15 % Ripple P-P 10 % or less |
| Tempo di risposta | OFF response: 25 ms or lessON response: 90 ms or less (auto reset) / 140 ms or less (manual reset) |
| Numero di prodotto | ST4-C11 |
| Uscite ausiliarie | PNP open-collector transistor / NPN open-collector transistor (Set using output polarity selection switch)ST4-C11: one outputST4-C12EX: four outputs[PNP output]Maximum source current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and +V)Residual voltage: 2.5 V or less (at 100 mA source current)[NPN output]Maximum sink current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and 0 V)Residual voltage: 2.0 V or less (at 100 mA sink current)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Uscita lampada di silenziamento | -(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Terminale di collegamento | Detachable spring-cage terminal |
| Consumo attuale | 100 mA or less (excluding sensor head ST4-Ax) |
| Norme applicabili | IEC 61496-1/2 (JIS B 9704-1/2 / UL 61496-1/2) (Type 4), ISO 13849-1:2015 (Category 4, PLe), JIS B 9705-1 (Category 4), IEC 61508-1 to 3 (SIL3), IEC 62061 (SIL3), JIS C 0508-1 to 3 (SIL3), UL 1998, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI/RIA R15.06, ANSI/ISA S84.01 (SIL3)(Note) Complies with those standards only when the controller is used in combination with the sensor head ST4-x. |
| Testa del sensore applicabile | ST4-Ax |
| Conformità alla direttiva sulla marcatura CE | Machinery Directive, EMC Directive, RoHS Directive |
| Uscite ausiliarie: Modalità di funzionamento | OFF when all beams of the connected ST4-Axs are receivedON when one or more beams of the connected ST4-Axs are interrupted |
| Uscite di controllo (OSSD 1, OSSD 2) | PNP open-collector transistor / NPN open-collector transistor Dual output x 1 system (Set using output polarity selection switch)[PNP output]Maximum source current: 200 mAApplied voltage: same as the supply voltage (between control output and +V)Residual voltage: 2.5 V or less (at 200 mA source current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. source current)Load wiring resistance: 3 Ohm or less (between control output and load)[NPN output]Maximum sink current: 200 mAApplied voltage: same as the supply voltage (between control output and 0 V)Residual voltage: 2.0 V or less (at 200 mA sink current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. sink current)Load wiring resistance: 3 Ohm or less (between control output and load)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Uscite ausiliarie: Circuito di protezione | Incorporated |
| Uscita lampada di silenziamento: circuito di protezione | Incorporated |
| Resistenza ambientale: umidità ambientale | 30 to 85 % RH, Storage: 30 to 95 % RH |
| Resistenza ambientale: resistenza agli urti | 300 m/s2acceleration in X, Y and Z directions three times each |
| Resistenza ambientale: temperatura ambiente | －10 to +55 ℃+14 to +131℉(No dew condensation or icing allowed),Storage: －25 to +70 ℃－13 to +158℉ |
| Resistenza ambientale: Grado di protezione | Enclosure: IP40 (IEC)Terminal: IP20 (IEC) |
| Resistenza ambientale: resistenza alle vibrazioni | 10 to 55 Hz frequency, 0.75 mm0.030 indouble amplitude or maximum acceleration 90 m/s2 in X, Y and Z directions for two hours each< |
| Resistenza ambientale: Resistenza di isolamento | 20 MOhm or more with 500 V DC mega between all supply terminals connected together and enclosure |
| Uscite di controllo (OSSD 1, OSSD 2): Modalità di funzionamento | ON when all beams of the connected ST4-Axs are receivedOFF when one or more beams of the connected ST4-Axs are interruptedOFF during lockout |
| Testa del sensore applicabile: numero di connessioni in serie | Interference prevention possible when up to a maximum of 6 sets are connected(When the maximum of 3 controllers are connected together, interference prevention is possible for up to 18 sets) |
| Uscite di controllo (OSSD1, OSSD2): Circuito di protezione | Incorporated |
| Resistenza ambientale: Sopportabilità della tensione | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
Descrizione del prodotto
Standard Control Unit Safety Barrier Category 4 Ple SIL 3, ST4 Series
Caratteristiche principali
- Qualità di grado industriale
- Conforme RoHS
- Certificato CE
- Garanzia di 1 anno
Documenti del prodotto
Scheda tecnica
Specifiche tecniche e dati di prestazione
Manuale utente
Guida di installazione e utilizzo
