Disponibile Prodotto più richiesto
UHLAC1P
UHLAC1P HLAC1P HL-AC1P PANASONIC HL-T1 sensor controller PNP, 12-24VDC
$0.00USD
4344 in magazzino
Specifiche chiave
Articolo:Specifications
Tipo:PNP output
Peso:Net weight: 140 g approx.
Dettagli:Controller (PNP output)
Informazioni fornitore
PANASONIC
Prodotti: 4316
Di solito spedito entro 2-3 giorni lavorativi
Qualità garantita
Spedizione veloce
Supporto tecnico
Specifiche tecniche
| Parametro | Valore |
|---|---|
| Articolo | Specifications |
| Tipo | PNP output |
| Peso | Net weight: 140 g approx. |
| Dettagli | Controller (PNP output) |
| Prodotto | Ultra-compact Laser Collimated Beam Sensor |
| Materiale | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| Cavo I/O | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| Numero di parte | HL-AC1P |
| Reimposta input | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Nome del prodotto | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| Input di temporizzazione | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Uscita lineare | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| Funzioni principali | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| Numero di prodotto | HL-AC1P |
| Tensione di alimentazione | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| Ingresso laser spento | +V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Ciclo di misura | 150 micro s |
| Grado di inquinamento | 3 (industrial environment) |
| Ingresso di azzeramento | +V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Consumo attuale | 190 mA or less (when connected to the sensor head) |
| Estensione del cavo I/O | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| Display sub-digitale | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| Display digitale principale | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| Resistenza di isolamento | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| Testa del sensore applicabile | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| Resistenza alla tensione | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Indicatori: Abilita (ENABLE) | Green LED (lights up during normal operation) |
| Indicatori: Risultati del giudizio | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| Indicatori: Azzeramento (ZERO) | Green LED (lights up when the zero reset function is enabled) |
| Frequenza di campionamento media impostabile | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| Conformità alla direttiva sulla marcatura CE | EMC Directive, RoHS Directive |
| Risultati del giudizio (ALTO, PASSATO, BASSO) | PNP open-collector transistor-Maximum source current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and +V)-Residual voltage: 2 V or less (at 50 mA source current) |
| Indicatori: Emissione laser (LD ON) | Green LED (lights up during laser emission) |
| Resistenza ambientale: Umidità ambientale | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Resistenza ambientale: Resistenza agli urti | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| Uscita lineare: Caratteristiche della temperatura | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| Resistenza ambientale: Temperatura ambiente | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| Resistenza ambientale: Resistenza alle vibrazioni | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| Uscite di giudizio (ALTO, PASS, BASSO): operazione di uscita | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| Uscite di giudizio (ALTO, PASSATO, BASSO): Numero di uscite | HIGH / PASS / LOW 3 values output |
| Risultati del giudizio (ALTO, PASSATO, BASSO): Categoria di utilizzo | DC-12 or DC-13 |
| Uscite di valutazione (HIGH, PASS, LOW): protezione da cortocircuito | Incorporated |
Descrizione del prodotto
HLT1 series controller, 12-24 VDC power, PNP digital output, selectable analog output between 4-20mA and ±4V
Caratteristiche principali
- Qualità di grado industriale
- Conforme RoHS
- Certificato CE
- Garanzia di 1 anno
Documenti del prodotto
Scheda tecnica
Specifiche tecniche e dati di prestazione
Manuale utente
Guida di installazione e utilizzo
