Disponibile Prodotto più richiesto
UHGS1010AC
UHGS1010AC HG-S1010-AC PANASONIC HG-S Sensor for measurement by contact. Head sensor with pneumatic actuator..
$0.00USD
4292 in magazzino
Specifiche chiave
Articolo:Specifications
Osservazione:Where measurement conditions are not specified, the conditions used were as follows: standard type measurement probe (HG-SS10C), ambient temperature of +20 ℃+68 ℉, and a clean atmosphere where water, oil, other liquids or dust does not come in contact with the equipment.
Colpo:10.5 mm0.413 inor more(Note) : The position that represents "0" as an absolute value is a position where the spindle is pushed further down from the bottom dead point by 0.1 mm0.004 inor more. The term "stroke" indicates the total stroke length from the bottom dead point to the top dead point.
Peso:Net weight: 80 g approx.
Informazioni fornitore
PANASONIC
Prodotti: 4316
Di solito spedito entro 2-3 giorni lavorativi
Qualità garantita
Spedizione veloce
Supporto tecnico
Specifiche tecniche
| Parametro | Valore |
|---|---|
| Articolo | Specifications |
| Osservazione | Where measurement conditions are not specified, the conditions used were as follows: standard type measurement probe (HG-SS10C), ambient temperature of +20 ℃+68 ℉, and a clean atmosphere where water, oil, other liquids or dust does not come in contact with the equipment. |
| Colpo | 10.5 mm0.413 inor more(Note) : The position that represents "0" as an absolute value is a position where the spindle is pushed further down from the bottom dead point by 0.1 mm0.004 inor more. The term "stroke" indicates the total stroke length from the bottom dead point to the top dead point. |
| Peso | Net weight: 80 g approx. |
| Dettagli | Air-driven type10 mm0.394 intype General purpose |
| Prodotto | Contact-Type Digital Displacement Sensor |
| Materiale | Body: Zinc, Holder: Stainless steel, Spindle: Tool steel, Probe (Note): Brass (body) / Ceramic (ball),, Air tube clamp: S60CM(Note) : The probe is also available as an option. |
| Accessorio | Sensor head fastening wrench: 1 pc., Mounting nut: 1 pc., Seal cap: 1pc, Air tube clamp: 1 pc. |
| Risoluzione | 0.5 μm0.02 mil |
| Numero di parte | HG-S1010-AC |
| Nome del prodotto | Contact-Type Digital Displacement Sensor HG-S |
| Fluido utilizzabile | Clean air (Dew point temperature: -10 ℃+14 ℉or less) |
| Frequenza di campionamento | 1 ms |
| Numero di prodotto | HG-S1010-AC |
| Tubo applicabile | Outside diameter: ø4 mmø0.157 in/ Inside diameter: ø2.5 mmø0.098 in |
| Misurazione della forza | ・Measuring force changes with the air pressure used. Removing the seal cap enables the product to be used as the low measuring force type.・For the relationship between supplied air pressure and measuring force or between measuring force and pushed spindle position, see the figures below. For upward mount without a seal cap, subtract 0.2 N from the measuring force. For side mount, subtract 0.1 N from the measuring force. The following figures are only typical examples, and these relationships differ depending on the assembly accuracy of the product or the abrasion status of sealing materials. |
| Campo di misura | 10 mm0.394 in(Note) : The position that represents "0" as an absolute value is a position where the spindle is pushed further down from the bottom dead point by 0.1 mm0.004 inor more. The term "stroke" indicates the total stroke length from the bottom dead point to the top dead point. |
| Metodo di messa a terra | Capacitor grounding |
| Grado di inquinamento | 2 |
| Funzione di sostituzione a caldo | Incorporated |
| Altitudine operativa | 2,000 m6561.68 ftor less(Note) : Do not use or store in an environment that has been pressurized to an air pressure higher than the atmospheric pressure at 0 m. |
| Indicatore di funzionamento | Equipped (2-color LED: Orange / Green) |
| Importo della deviazione della mancia | 35 μm1.378 mil(typical value) |
| Controller applicabile | HG-SC101(-P), HG-SC111(-P), HG-SC112(-P), HG-SC113(Note) : Be sure to use the sensor in combination with an HG-SC□ controller manufactured in or after February 2019. |
| Resistenza di isolamento | 100 MΩ or more at 250 V DC |
| Conformità normativa | CE Marking (EMC Directive, RoHS Directive), UKCA Marking (EMC Regulations, RoHS Regulations) |
| Gamma di pressione di lavoro | 0.14 to 0.16 MPaWith no seal cap mounted : 0.035 to 0.045 MPa |
| Precisione dell'indicazione (PP) | Full range: 2.0 μm0.079 milor lessLimited range: 1.0 μm0.039 milor less(any 60 μm2.362 mil) |
| Metodo di rilevamento della posizione | Optical absolute linear encoder method |
| Capacità di resistere alla pressione | 0.2 MPa |
| Resistenza ambientale: Protezione | IP67 (IEC)With no seal cap mounted : -(Note) : Protective structure is not applicable when the sealing portions have deteriorated or become damaged. The protection level is zero when the seal cap is removed. |
| Resistenza ambientale: Umidità ambientale | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Resistenza ambientale: Resistenza agli urti | 1,960 m/s2acceleration in X, Y, and Z directions three times each |
| Resistenza ambientale: Temperatura ambiente | -10 to +55 ℃+14 to +131 ℉(No dew condensation or icing allowed),Storage: -20 to +60 ℃-4 to +140 ℉ |
| Resistenza ambientale: Resistenza alle vibrazioni | 10 to 500 Hz frequency, 3 mm0.118 indouble amplitude (10 to 58 Hz), maximum acceleration 196 m/s2, (58 to 150 Hz) in X, Y, and Z directions for two hours each |
Descrizione del prodotto
HG-S - Contact measurement sensor. Sensor head with pneumatic actuator. Resolution 0.5μm. Precision 2μm. Range 10mm
Caratteristiche principali
- Qualità di grado industriale
- Conforme RoHS
- Certificato CE
- Garanzia di 1 anno
Documenti del prodotto
Scheda tecnica
Specifiche tecniche e dati di prestazione
Manuale utente
Guida di installazione e utilizzo
