Disponibile Prodotto più richiesto
LCM-40KN
LCM-40KN MEANWELL AC-DC Multi-Stage LED driver Constant Current (CC), Modular output 0.35A/0.5A/0.6A/0.7A/0...
$0.00USD
4187 in magazzino
Specifiche chiave
Nome (dettagli):LCM-40KN
Potenza (dettagli):42W
Stato (dettagli):New
Stock (dettagli):Yes
Informazioni fornitore
MEANWELL
Prodotti: 6448
Di solito spedito entro 2-3 giorni lavorativi
Qualità garantita
Spedizione veloce
Supporto tecnico
Specifiche tecniche
| Parametro | Valore |
|---|---|
| Nome (dettagli) | LCM-40KN |
| Potenza (dettagli) | 42W |
| Stato (dettagli) | New |
| Stock (dettagli) | Yes |
| Formato (dettagli) | Box |
| Serie (dettagli) | LCM-40KN |
| Approvazioni (dettagli) | CCC, CE, EAC, ENEC, MM |
| Potenza (W) (Dettagli) | 42,00 |
| Regolamento (dettagli) | KNX |
| Subformato (Dettagli) | IP20 |
| Larghezza (mm) (Dettagli) | 81.50 |
| Altezza (mm) (Dettagli) | 23.00 |
| Ingresso CA Max (Dettagli) | 295,00 |
| Ingresso CA Min (Dettagli) | 180,00 |
| Applicazioni (dettagli) | Lighting |
| Produttore (dettagli) | MEAN WELL |
| Tipo di prodotto (dettagli) | LED Driver |
| Isolamento (V) (Dettagli) | 3.750,00 |
| Corrente di uscita (dettagli) | 350mA |
| Potenza di picco (W) (Dettagli) | Forty two |
| Connettore di ingresso (dettagli) | Quick Connector |
| Frequenza di ingresso (dettagli) | 50 Hz, 60 Hz |
| Lungo/Sfondo (Dettagli) | 123.50 |
| Descrizione lunga (dettagli) | LED driver dimmable by signal KNX and a push button.Specially designed for powering LEDs directly in a steady stream.Format in plastic boxIP20.Input range180-295Vca47-63Hz.Current output selectable by micro-switch350, 500, 600, 700, 900 or 1050mA.Output current350mA500mA600mA700mA900mA1050mAPower42W42W42W42W42W42WRange of Output Voltage2-100Vcc2-80Vcc2-67Vcc2-57Vcc2-45Vcc2-40VccEfficiency typical:90%.Regulationsignal-KNX and a push button.Functions: dimming, manual, hours of operation, and feedback of energy consumption.Synchronization: we can sync up10 unitsvia the wires LCM-xxx-SYNC in such a way that by regulating a source other do the same regulation.Input class II without grounding.Factor corrector, power>0,975to 230vac at full load.Linear curve or a logarithmic programmableinterfacepush button KNXintegrated.Supportemergency lighting(THE).Possibility of programmingCLO (Constant Light Output).Operating temperature range of caseTcfrom-30ºCup+90ºC.Dimensions (Length x Width x Height):123,5 x to 81.5 x 23mm.3 years of warranty.Manufacturer: MEAN WELL.VIDEO LCM-40KN - FIRST LED DRIVER MULTICORRIENTE KNX.This source is designed to work directly with leds (plates LED or COBs), not with LED strips. Must be equipment that is fed in a steady stream.This source works on a constant Current when we connect the LEDs directly to have a voltage within the range of rensión output mode constant current and a working current equal to the output current.Be sure to adjust the output current desired using the selector outlet.For more information please see the datasheet in the section attachments.This version (KN) is governed by the protocolKNX. With multiple levels selectable through DIP switch and the KNX interface. We can regulate directly by KNX without the need of the typical gateway KNX-DALI. The input range is 180-295Vca and offers different levels of current, ranging from 350-1050mA.These drivers have a high efficiency (90%) and a fanless design, being able to work at temperatures (of the box) between -30 ° C and +90 ° C. in Addition, we have the ability to schedule the CLO (Constant Light Output), which increases with the hours of operation, the output current, to always maintain the same brightness and save energy, while increasing the life of the leds.With plastic housing, designed for applications of LED lighting. Suitable for indoor lighting, modern constructions and intelligent or buildings-houses refurbished for not rewiring, stairs (with two buttons on the same switch) and outdoor applications.Low ripple current, no flicker (flicker-free).Input for protection by temperature of the LED modules. The driver has an input to connect a NTC sensor (resistance of a negative coefficient) which allows us to reduce the output current in case of excess of temperature in the LED modules. If we're not going to use this input protection, we can use it to connect a fixed resistor and adjust the output current to values lower intermediate up to 56% lower than the value selected with the DIP-Switch. For example if we want a current of 630mA we can adjust the output with the jumpers to 700mA and connect a resistor of 34kOhmnios. For more information please see the datasheet in the tab "Attachments" and you can use the Excel file to calculate the value of the resistance.Some of the sensors supported are:MEAN WELL: WPD-06SWT Push button dual wireless, without batteries.MEAN WELL: NWC-300 programmer EnOcean USB for the configuration of the system.MEAN WELL: EOSWA-W-EO sensor of presence of a wall.MEAN WELL: EOSCA-W-EO sensor of presence of roof.MEAN WELL: ELLSU-W-EO brightness sensor. |
| Connettore di uscita (dettagli) | Quick Connector |
| Tipo di ingresso CA (dettagli) | Single-phase |
| Garanzia (anni) (dettagli) | 3,00 |
| Paese di origine (dettagli) | China |
| Corrente di uscita mA (Dettagli) | 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 1050 |
| Potenza (Informazioni aggiuntive) | 42W |
| Gamma di tensione di uscita (dettagli) | 2-100Vcc |
| Corrente di uscita (Informazioni aggiuntive) | 350mA |
| Intensità di uscita minima (mA) (dettagli) | 350,00 |
| Intensità di uscita massima (mA) (dettagli) | 1.050,00 |
| Gamma di tensione di uscita (informazioni aggiuntive) | 2-100Vcc |
Descrizione del prodotto
More details
Caratteristiche principali
- Qualità di grado industriale
- Conforme RoHS
- Certificato CE
- Garanzia di 1 anno
Dettagli tecnici
LED driver dimmable by signal KNX and a push button.
Documenti del prodotto
Scheda tecnica
Specifiche tecniche e dati di prestazione
Manuale utente
Guida di installazione e utilizzo
