Disponibile Prodotto più richiesto
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46USD
326 in magazzino
Specifiche chiave
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Tipo:D7
Test:DIN VDE 0627/86
Larghezza:21 mm
Informazioni fornitore
Prodotti: 0
Di solito spedito entro 2-3 giorni lavorativi
Qualità garantita
Spedizione veloce
Supporto tecnico
Specifiche tecniche
| Parametro | Valore |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Tipo | D7 |
| Test | DIN VDE 0627/86 |
| Larghezza | 21 mm |
| Altezza | 34.8 mm |
| Lunghezza | 21 mm |
| Serie | HC-HS |
| Generale | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| Applicazione | Power |
| Tipo di prodotto | Contact insert with a fixed no. of positions |
| Nota di montaggio | To ensure correct use, installation in housing with IP54 protection or better is required |
| Corrente nominale | 40 A |
| Revisione dell'articolo | 04 |
| Diametro di contatto | 4 mm |
| Materiale di contatto | Copper alloy |
| Presa esagonale | SW2,0 |
| Numerazione dei contatti | 1 - 2 |
| Coppia di serraggio | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| Profilo di connessione | 2+PE |
| Grado di inquinamento | 3 |
| Disegno dimensionale | |
| Numero di posizioni | 2 |
| Tensione di sovratensione nominale | 6 kV |
| Categoria di sovratensione | III |
| Tecnologia di connessione | Axial screw connection |
| Tipo di materiale di contatto | turned |
| Numero di contatti di potenza | 2 |
| Tensione nominale (III/3) | 400 V |
| Sezione trasversale del conduttore | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| Materiale portante del contatto | PC |
| Materiale della superficie di contatto | Ag |
| Cicli di inserimento/ritiro | ≥ 500 |
| Sezione trasversale di collegamento AWG | 10 ... 8 |
| Temperatura ambiente (funzionamento) | -40 °C ... 125 °C (including heating up of contacts) |
| Collegamento secondo lo standard | IEC / EN |
| Norme costruttive e di collaudo | DIN VDE 0627/86 |
| Grado di infiammabilità secondo UL 94 | V0 |
| Lunghezza di spelatura del singolo filo | 8 mm +1 mm |
Descrizione del prodotto
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
Caratteristiche principali
- Qualità di grado industriale
- Conforme RoHS
- Certificato CE
- Garanzia di 1 anno
Documenti del prodotto
Scheda tecnica
Specifiche tecniche e dati di prestazione
Manuale utente
Guida di installazione e utilizzo
